IHI 55N3 Скачать руководство пользователя страница 63

Страница: 63 / 115

2 – 21

ᵐ

ATI

STEERING CONTROL

* Be sure no one is working on or near the machine to prevent injury.

Keep the machine under control at all times to prevent injury.

* Before control levers, confirm which direction the track frame faces.
* Always travel with sprockets under the rear of the machine.

1. Move engine throttle lever

to the operating

range.

2. Move the travel lever lock and control shut-off

lever to the unlocked position.

3. Raise the boom and the blade enough to provide

sufficient ground clearance.

STEERING

To make turns, control the travel levers.
Control the two travel levers as follows.

Pivot Left Turn

Move the right lever

forward to travel forward

and left, and move it rear to travel reverse and left,
pivoting on the left track.

Pivot Right Turn

Move the left lever

forward to travel forward

and right, and move it rear to travel reverse and
right, pivoting on the right track.

SPOT TURN
Spot Left Turn

Move the left travel lever

rear and move the

right lever

forward at the same time. This

allows a quick left turn.

Spot Right Turn

Move the right travel lever

rear and move the

left lever

forward at the same time, allowing a

quick right turn.

Forward

teering

Reverse

teering

top the

left track

IVOT LEFT TURN

➀

WARNING

Forward

teering

Reverse

teering

top the

left track

IVOT RIGHT TURN

OT LEFT TURN

Содержание 55N3




















































































































Результаты поиска

Содержание 55N3

Отзывы:

IHI 55N3, Руководство по эксплуатации, Страница: 63 / 115

Результаты поиска

Содержание 55N3

Отзывы: