IHI 55N3 Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 115

IHI 55N3 Скачать руководство пользователя страница 87

3 – 17

ᵑ

MAINTENAN

C

E

4. Clean the inside of the cleaner housing

e

and

service cover

c

.

NOTE:

Clean the seal tube in the cleaner housing.

Dust on the seal tube causes dust leak.

5. Primary element

d

can be cleaned with

compressed air 200 kPa (2 kgf/cm

2

) maximum.

Direct air along pleats inside of filter element.

6. Inspect the filter element after cleaning. Do not

use a filter element with damaged pleats, gasket
or seals.

NOTE:

The used element may be useful to find a

foreign substance on the seal surface of the filter
element, which can cause leak. If the striped dust
is seen on the seal surface, it is a symptom of dust
leak. If such dust seen, inspect if there are foreign
substances, on the inside and outside of the
housing seal tube.

7. Install a clean primary element

d

. Install and

secure the service cover

c

with the valve

g

at

the bottom.

NOTE:

Insert a new element correctly. When the

element seal unit is inserted into the seal tube, its
seal surface is extended uniformly to seal the
element. To seal the element more accurately,
push securely not the center but the outer of the
element end surface.

8. Reset the dust indicator

h

by pushing in the reset

button.

9. If the dust indicator indicated the red signal after

starting the engine, change to new element.

NOTE:

Normally a filter can be cleaned up to five

times. Replace after five cleanings maximum.

Cleaning Element

Inspect Primary Element

Install Primary Element

YES

NO

YES

Indicator

Reset button

250HOURS

«
...
85
86
87
88
89
...
»

Содержание 55N3




















































































































Отзывы:

Нет отзывов