IHI 55N3 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 115

IHI 55N3 Скачать руководство пользователя страница 40

1 – 34

ᵏ

SAFETY

Illustrated
symbol

Recommended
explanation

Illustrated
symbol

Recommended
explanation

g

Sign indicates a hazard
of being hit by the
working device of the
machine.
Keep away from machine
during operation.
• Part No.: D405 511 00

h

Sign indicates a hazard
of rotating parts, such as
belt.
Turn off before inspection
and maintenance.
• Part No.: D405 366 00

f

Sign indicates a hazard
of rotating parts, such as
fan.
Turn off before inspection
and maintenance.
• Part No.: D405 509 00

c

Warning!
Read manual before
operation, maintenance,
disassembly, assembly
and transportaion.
• Part No.: D405 359 00

e

Sign indicates a hazard
of being crushed or run
over by unexpected
moving of stopped
machine.
Lower working device to
ground, move safety
lever to lock position
and take engine key
with you before leaving
machine.
• Part No.: D405 508 00

d

Sign indicates an
electrocution hazard if
machine is brought too
near electric power lines.
Keep a safe distance
from electric power lines.
• Part No.: D405 506 00

«
...
38
39
40
41
42
...
»

Содержание 55N3




















































































































Отзывы:

Нет отзывов