IHI 55N3 Скачать руководство пользователя страница 94

Страница: 94 / 115

3 – 24

ᵑ

MAINTENAN

1000HOURS

Change Hydraulic Oil and Clean the Strainer

* Hot oil and components can cause personal

injury. Do not allow hot oil or components to
contact the skin.

* At operating temperature, the hydraulic tank

is hot and can be under pressure.

* To relieve the pressure from the hydraulic

tank, loosen the oil fill plug

on the

hydraulic tank.

* Relieve the tank pressure with engine off by

removing fill plug slowly to prevent burns
from hot oil.

1. Place the machine on level ground, with the arm

and bucket cylinder fully retracted and
attachments lowered, as shown. Stop the engine.

2. Relieve the internal pressure from the hydraulic

tank by loosening the fill plug

3. Clean area thoroughly to keep dirt out of strainer

cover unit

and fill plug

4. Remove the oil drain plug

. Drain oil into a

container. Drain oil in all parts of the hydraulic
system thereafter.

NOTE:

Always dispose of used oil as established

by local regulation.

5. Remove the pipe joint

. Remove the bolts

and the strainer cover unit

/strainer

from

the hydraulic tank.

6. Inspect the O-ring

and replace it if damaged.

7. Clean the inside of the tank with the clean oil.

8. Clean and install the strainer cover unit

strainer

and the pipe joint

9. Clean and install the drain plug

CAUTION

Bucket position at the time of

drain the hydraulic oil.

Содержание 55N3




















































































































Результаты поиска

Содержание 55N3

Отзывы:

IHI 55N3, Руководство по эксплуатации, Страница: 94 / 115

Результаты поиска

Содержание 55N3

Отзывы: