IHI 55N3 Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 115

IHI 55N3 Скачать руководство пользователя страница 113

7 – 6

ᵕ

SPE

C

IFI

C

ATI

O

NS

7-4 RATED OBJECT HANDLING CAPACITIES TABLE

Working conditions:

– with bucket.
– on a compact horizontal level ground.
– in complete swing of the upperstructure.

These lords are value for the height of the
considered zone ( Z. ) for the intended
outreach.

LIFTING CAPACITY

This lifting capacity is applied for operation
on a level and firm ground. If the machine
is operated on an unleveled or unstable
ground, the capacity decreases.

CAUTION

There may be some local government regulations regarding the
use of excavators to lift heavy objects. Please observe those
regulations where they apply.

Outreach in m - Loads in kg

Outreach (m)

6.0

6.5

5.0

4.5

4.0

3.5

3.0

2.5

2.0

Z2

500

600

700

900

1100 1300 1700

Z1

400

500

500

600

700

900

1200 1500 1600

Z3

600

700

900

1000 1300 1600

Boom length

3.0m

Arm length

1.55 m / 1.85 m

«
...
111
112
113
114
115
»

Содержание 55N3




















































































































Отзывы:

Нет отзывов