IHI 55N3 Скачать руководство пользователя страница 46

Страница: 46 / 115

2 – 4

ᵐ

ATI

2. GAUGES and METER

Fuel Level Gauge

It indicates the amount of in the fuel tank. Add fuel
immediately when the gauge indicates the level
is in the

range.

F :

The fuel tank is full.

E :

Fuel level is too low.

Water Temperature Gauge

This indicates the engine coolant temperature.
Upon start-up, the lowest

“White”

range

indicates. While running the engine, with out load
and low idling warming up.
The

“Green”

range is the normal operating

temperature.
The

“Red”

range indicates overheating.

If the gauge indicate red range, reduce machine
operating speed and keep the engine at low idle
until the engine is cooled down. Stop the engine.
Check the coolant. Check the fan drive belt. Have
any necessary repair made.

Service Hour Meter

Indicates the total operating hours of the
machine.
It should be used to determine service hour
maintenance intervals.

3. SWITCHES

Light Switch

Push down on the [

] marked of the switch to

turn the light on.
Push down on the blank half of switch to turn the
working light off.

Green

Red

Green

Red

White

LIGHT

Содержание 55N3




















































































































Результаты поиска

Содержание 55N3

Отзывы:

IHI 55N3, Руководство по эксплуатации, Страница: 46 / 115

Результаты поиска

Содержание 55N3

Отзывы: