IHI 55N3 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 115

IHI 55N3 Скачать руководство пользователя страница 41

1 – 35

ᵏ

SAFETY

&101612'4#6'

&

Illustrated
symbol

Recommended
explanation

Illustrated
symbol

Recommended
explanation

i

Sign indicates a burn
hazard from spurting
hot water or oil if
radiator or hydraulic oil
tank is uncapped while
hot.
Allow radiator or
hydraulic oil tank to cool
before removing cap.
• Part No.: D405 360 00

j

Sign indicates an electrical
hazard from handing the
cable.
Read manual for safe and
proper handing.
• Part No.: D405 363 00

k

Sign indicates a crush hazard by rotation
of upper structure of the machine.
Keep away from swinging area of machine.
• Part No.: D406 022 00

l

Sign indicates a hazard of flying plug from
track adjuster that could cause injury.
Read manual before adjusting track for
safe and proper handling.
• Part No.: D405 505 00

11

Sign indicates a hazard from falling window.
After raising window, be sure to lock it in place with
lock pins.
• Part No.: D405 510 00
(For the cabin mounted machine only.)

DANGER!

Operation prohibition during inspection and servicing.
Hang this sign on the control lever during inspection and
servicing not to allow any other worker to start the engine or
operate the machine.
• Part No.: D405 323 00

12

«
...
39
40
41
42
43
...
»

Содержание 55N3




















































































































Отзывы:

Нет отзывов