IHI 55N3 Скачать руководство пользователя страница 93

Страница: 93 / 115

3 – 23

ᵑ

MAINTENAN

1000HOURS

3-8 1000 HOURS MAINTENANCE AND CHECKS

Change the Travel Reduction Gear Oil

1. Position one travel reduction gear with drain plug

at the bottom.

2. Remove the drain plug, oil level plug

and oil fill

plug

. Allow the oil to drain into a container.

NOTE:

Dispose drained material according to local

regulation.

3. Clean and install the drain plug.

4. Fill the oil to bottom of level plug opening.

Refill capacities

5. Clean and install the oil level plug and oil fill plug.

6. Perform procedure on the other travel reduction gear.

7. Start the engine and allow the travel reduction gear to

turn through several cycles.

8. Stop the engine, check the oil level.

9. Check the drained oil for metal chips or particles. If

there are any, consult your IHI dealer.

Serial number

Reduction Gear

Capacity

WP003001 ~ WP003154

1.3 Liter

WP003155 ~

1.1 Liter

IL L.

Содержание 55N3




















































































































Результаты поиска

Содержание 55N3

Отзывы:

IHI 55N3, Руководство по эксплуатации, Страница: 93 / 115

Результаты поиска

Содержание 55N3

Отзывы: