IHI 55N3 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 115

IHI 55N3 Скачать руководство пользователя страница 28

1 – 22

ᵏ

SAFETY

1-7 SAFE TRAVEL

ALWAYS CHECK THE TRAVEL
DIRECTION.

ALWAYS

check in which direction the

superstructure faces before controlling the
travel levers. The machine is likely to travel in
the opposite direction to your expectation
when the superstructure directly faces to the
rear.

MAINTAIN OVERHEAD CLEARANCES.

ALWAYS

be on the alert for overhead

obstacles and be sure there is adequate side
clearance when traveling. Get the assistance
of the man on the ground when clearances
cannot be ascertained from the operator’s
position.

CAREFULLY TRAVEL THE MACHINE IN A
NARROW AREA AND LOW CLEARANCE.

NEVER

travel in an area where persons are

coming and going or there are many objects.

ALWAYS

keep a safety distance around the

machine. In a narrow area, place a signal
person to guide the operator.
Before traveling, keep away persons from the
traveling range.

«
...
26
27
28
29
30
...
»

Содержание 55N3




















































































































Отзывы:

Нет отзывов