IHI 55N3 Скачать руководство пользователя страница 79

Страница: 79 / 115

3 – 9

ᵑ

MAINTENAN

WHEN REQUIRED

REPLACE THE TEETH AND SIDE
CUTTERS

* Personal injury or death can result

from bucket falling

* Block the bucket before changing

bucket tooth or side cutter.

Replacement Period of Tooth

Replace the bucket tooth when a wear
hole appears.

Replacement of Tooth

1. Drive the lock pin from the worn tooth.

Remove the tooth.

2. Clean the adaptor and pin hole.
3. Install the new rubber pin into the tooth.
4. Install the new tooth over the adaptor.
5. Drive the lock pin through the tooth, until

the pin is flush with the tooth surface.

NOTICE:

After driving the lock pin, make sure the
lock pin fits snugly into the hole of the
tooth.

Replacement of Side Cutters

1. Remove the mounting bolts and remove

the side cutters.

2. Clean the mounting surfaces. Install the

new side cutters.

WARNING

Change

Over use

Nose section

Tooth pin

Rubber pin lock

Adaptor

Tooth

Nut

Washer

Side cutter (R.H.)

Bolt

Side cutter (L.H.)

Block

Hole

Rubber

Wrong

Tooth pin Length

short-end.

Tooth pin

Typical Example

Содержание 55N3




















































































































Результаты поиска

Содержание 55N3

Отзывы:

IHI 55N3, Руководство по эксплуатации, Страница: 79 / 115

Результаты поиска

Содержание 55N3

Отзывы: