manualshive.com logo in svg

IHI 55N3, Руководство по эксплуатации, Страница: 7 / 115

Поделиться
Скачать
IHI 55N3 Скачать руководство пользователя страница 7

1 – 1

ᵏ

SAFETY

SAFETY TIPS

This section explains safety tips which you
will find throughout this manual and on the
machine.
Periodically check labels and plates
containing those tips for damage.
If they are damaged, clean or replace them.
For replacement, contact your local 

IHI

 dealer

with their Parts Numbers in the Parts
Catalogue.

Remember that the safety tips that we
provide cannot cover every kind of danger
that you may encounter during operation.

1-1  GENERAL

OBSERVE THE BASICS FOR SAFE AND
EFFECTIVE OPERATION.

The operator's knowledge, skills, and
experience are the most important to utilize
the machine. Therefore, be sure to
understand operation procedures and to take
necessary training.

OPERATOR SHOULD BE QUALIFIED.

Only qualified operators should be authorized
to operate the machine, and those so
authorized should do so only when physically
and mentally alert.
The operator should be to be familiar with the
hazards and necessary safety measures
unique to the operation of hydraulic
excavators.

Содержание 55N3




















































































































Отзывы:

Нет отзывов