IHI 55N3 Скачать руководство пользователя страница 64

Страница: 64 / 115

2 – 22

ᵐ

ATI

HIGH SPEED TRAVEL

Do not change travel speed ranges while going
downhill.

NEVER

high speed travel on a grade or

loading and unloading the machine.
When control shut-off lever is locked, does not
shift to high speed travel.

Push down the high speed travel pedal

shift to

the high speed travel.
When released pedal, shift to the low speed
travel.

CAUTION ON TRAVEL ON A GRADE

* Reduce engine speed when maneuvering in

tight quarters or when breaking over a rise.

* Do not change travel speed ranges while

going downhill.

* Work up and down slopes rather then

sideways, whenever possible.
Do not travel across a grade by all means.

* Avoid changing the direction of travel on a

slope, which could result in tipping or side
slipping of the machine.

* Keep the arm in and carry the boom in a low

position.

* When starting up a steep grade or breaking

over a rise, keep the boom lowered as close
to the ground as possible.

1. When traveling up on a grade inclining by

greater than 15°, keep the position in the right
illustration and travel with a low engine speed.

2. When traveling down on a grade inclining by

greater than 15°, travel with the position in the
right illustration.

CAUTION

Содержание 55N3




















































































































Результаты поиска

Содержание 55N3

Отзывы:

IHI 55N3, Руководство по эксплуатации, Страница: 64 / 115

Результаты поиска

Содержание 55N3

Отзывы: