IHI 55N3 Скачать руководство пользователя страница 62

Страница: 62 / 115

2 – 20

ᵐ

ATI

2-10 TRAVELING THE MACHINE

STRAIGHT TRAVEL

* Be sure no one is working on or near the machine to prevent injury.

Keep the machine under control at all times to prevent injury.

* Before control levers, confirm which direction the track frame faces.
* Always travel with sprockets under the rear of the machine.

1. Move engine throttle lever

to the operating

range.

2. Move the control shut-off lever

to the unlocked

position.

3. Raise the boom and the blade enough to provide

sufficient ground clearance.

4. Control right and left travel levers

as follows.

Forward Direction Travel

Move the both travel levers

forward to move

the machine forward.
The machine will always travel toward the

BLADE.

Stop

Slowly move both the travel levers

to the stop

position to stop the machine and apply the
brakes.

Reverse Direction Travel

Move the both travel levers

rear to move

the machine reverse.
The machine will always travel toward the

SPROCKETS.

Travel
lever
(L.H.)

Travel
lever
(R.H.)

Forward
Travel

Reverse
Travel

WARNING

Содержание 55N3




















































































































Результаты поиска

Содержание 55N3

Отзывы:

IHI 55N3, Руководство по эксплуатации, Страница: 62 / 115

Результаты поиска

Содержание 55N3

Отзывы: