IHI 55N3 Скачать руководство пользователя страница 86

Страница: 86 / 115

3 – 16

ᵑ

MAINTENAN

* Service the air cleaner if indicated the

red signal in the dust indicator with the
engine running at high idle.

* Service the air cleaner only with the

engine stopped to prevent engine
damage.

* Do not clean the filter elements by

bumping or tapping them.
Do not use filter element with the
damaged pleats, gaskets or seals.
Engine damage could result.

* When using pressure air for cleaning,

wear a protective face shield or
protective grasses.

Service the Filter Elements

CAUTION

Service the Primary Element

Cleaning: Every 250 hours or when indicated the

red signal in the dust indicator.

Replacement: After cleaning five times, after one

year or damaged pleats or seals.

1. Stop the engine.
2. Release the two latches and remove the service

cover

3. Remove the primary element

from the air

cleaner housing

Do not remove the secondary element

, when

service the primary element

only.

NOTE:

Remove the seal unit of element gently. The

element is radially sealed by the element seal unit
and seal tube. To loose the seal unit, move the
outer of element gently up and down or right and
left or turn the element to remove it.
Take out the element not to scatter dust.

Содержание 55N3




















































































































Результаты поиска

Содержание 55N3

Отзывы:

IHI 55N3, Руководство по эксплуатации, Страница: 86 / 115

Результаты поиска

Содержание 55N3

Отзывы: