IHI 55N3 Скачать руководство пользователя страница 22

Страница: 22 / 115

1 – 16

ᵏ

SAFETY

TOPS THAT PROTECTS YOU FROM
BEING CRUSHED BY THE TIPPED-
OVER MACHINE

The cab-type machine is equipped with a

TOPS

(Tip over protective structure) as a

standard specification.
The canopy-type machine is not equipped
with a

TOPS

as standard, however, when

the danger of turnover is expected while
working on a soft, uneven, or included, we
recommend the use of

TOPS canopy

Be sure to fasten the seat belt while operating
the machine

NEVER

try to jump out of the cabin when the

machine falling down. This may crash an
operator to serious injury or death.

TOPS canopy

is avoidable as option.

Consult your local

lHl

dealer.

THE FRONT GUARD PROTECTS AN
OPERATOR FROM FLYING OBJECTS
THE FRONT.

When braking materials with the machine
and objects are likely to fly from the front, the

front guard

shall be equipped. If it is not

equipped, flying objects may cause injury or
death.

The front guard is avoidable as option.
Consult your locaI

IHI

dealer.

FOPS (TOP GUARD) PROTECTS AN
OPERATOR FROM FLYING OBJECTS.

When working underneath cliff or destroying
a building with the machine, the

top guard

shall be equipped.
Use the top guard to protect the operator and
watch falling object. Otherwise falling objects
may cause injury or death.
The top guard is avoidable as option. Consult
your local

lHl

dealer.

FOPS:

Falling-object protective structure.

Stay in cabin

Never try to jump out

Содержание 55N3




















































































































Результаты поиска

Содержание 55N3

Отзывы:

IHI 55N3, Руководство по эксплуатации, Страница: 22 / 115

Результаты поиска

Содержание 55N3

Отзывы: