IHI 55N3 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 115

IHI 55N3 Скачать руководство пользователя страница 8

1 – 2

ᵏ

SAFETY

READ AND UNDERSTAND THE
INSTRUCTIONS AND WARNINGS.

This manual, plates, and labels on the
machine contain necessary instructions and
warnings for safe operation. You are supposed
to read and understand them first.
If you should ignore them, injury or death may
occur. Do not leave what you do not
understand as it is. Your

IHI

distributor is glad

to answer any question.
If the manual, plate, or label is missing or
damaged, contact

lHl

distributor for

replacement.

OPERATOR SHOULD BE IN GOOD
HEALTH.

Operator should be physically and mentally
alert, which is one of the best insurance
against an accident.

NEVER

operate the machine under the

influence of alcohol, medication or intoxication.

WEAR PROPER WORKING CLOTHES.

Wear working clothes that closely fit
operators. Avoid loose jackets, shirt sleeves,
rings, and other jewelry which may be caught
in moving parts. Avoid also oil stained or
damaged garments. Shoes should be clear of
grease or mud before operation.
Always wear required protective items such
as hard hats, safety glasses, reflective
clothing. safety shoes, and ear protection as
required.

«
...
6
7
8
9
10
...
»

Содержание 55N3




















































































































Отзывы:

Нет отзывов