IHI 55N3 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 115

IHI 55N3 Скачать руководство пользователя страница 36

1 – 30

ᵏ

SAFETY

PREVENT FIRE OR EXPLOSIONS.

Keep away fuel, lubricant, and coolant from
any fire or heat. Most of them are very
flammable.

NEVER

place flammable materials or objects

close to fire or heat.

NEVER SMOKE WHILE REFUELLING.

NEVER

smoke while refuelling or in a place

close to flammable objects.

DO NOT TOUCH BATTERY
ELECTROLYTE.

Battery post, terminals and related accessories
contain lead and lead compounds. Wash hands
after handling.

Battery acid will

burn skin,

eat holes in

clothing, and

cause blindness

if splashed

into eyes. If you spill acid on yourself flush
skin immediately with lots of water. Apply
baking soda to help neutralize the acid.
If acid gets in your eyes, flush immediately
with large amount of water and seek proper
medical treatment immediately.

When servicing battery

remember that a

lead-acid storage battery generates (when
charging or discharging) hydrogen and
oxygen – a very explosive mixture. A spark or
flame could ignite these gases.

Always wear

safety grasses and groves

when working with battery.

Eye protection required

«
...
34
35
36
37
38
...
»

Содержание 55N3




















































































































Отзывы:

Нет отзывов