IHI 55N3 Скачать руководство пользователя страница 48

Страница: 48 / 115

2 – 6

ᵐ

ATI

4. MACHINE CONTROLS

Engine Throttle Lever

Decrease

(1): Move the lever to forward to

decrease the engine speed.

Increase

(2): Move the lever to the rear to

increase the engine speed.

Control Shut-off Lever (Left and Light Levers)
(for all hydraulic activation controls)

To mounting and dismounting the machine, be
sure to put the shut-off lever in the

LOCKED

position.
If the lever is in the

UNLOCKED

position,

upper structure can swing and can result
personal injury.

Locked

: Move the lever back to the locked

position. This makes all hydraulic activation
controls inoperable.

Unlocked

: Move the lever forward to the

unlocked position. This makes all hydraulic
activation controls operable.

High Speed Travel Pedal

NEVER

high speed travel on a grade or

loading and unloading the machine.

* When control shut-off lever is locked, does

not change to high speed travel.

Low Speed Travel

Release the pedal to low speed travel. Select the

LOW

speed travel when driving on rough or soft

surface. Low is also recommended for loading or
unloading from a truck.

High Speed Travel

During push down the pedal to shift the high
speed travel. Select the

HIGH

speed travel when

driving on a hard even surface.

CAUTION

Содержание 55N3




















































































































Результаты поиска

Содержание 55N3

Отзывы:

IHI 55N3, Руководство по эксплуатации, Страница: 48 / 115

Результаты поиска

Содержание 55N3

Отзывы: