IHI 55N3 Скачать руководство пользователя страница 70

Страница: 70 / 115

2 – 28

ᵐ

ATI

2-16 PARKING THE MACHINE

At the end of a day’s work, following steps should be
observed as the established machine shut-down
procedure:

Machine Stopping

Park on a level surface, if necessary to park on a
grade, block the tracks securely.
1. Move engine throttle lever forward to reduce the

engine speed.

2. Release the travel lever to stop the machine.
3. Lower the bucket to the ground and apply slight

down pressure.

4. Move the control shut-off lever to the

LOCKED

position.

Freezing Conditions

If freezing temperature are expected, each crawler
frame should be cleaned of mud and dirt and the
machine parked on wood planks.

Engine Stopping

1. Operate the engine at

LOW IDLE

for five minutes.

This gives the engine a chance to cool off
gradually before they are stopped.

2. Turn the start switch key to

OFF.

Remove the

key.

Leaving the Machine

1. Use the steps and handhold, use both handles

and face the machine, when dismounting.

2. Inspect the entire machine for leaks, loose

connections, signs of wear, crack etc. Report any
signs of trouble discovered during this inspection.

3. Close and lock the doors.

2-17 EMARGENCY ENGINE STOP

To stop the engine in emergency, turn the start switch key to

“OFF”

position.

Содержание 55N3




















































































































Результаты поиска

Содержание 55N3

Отзывы:

IHI 55N3, Руководство по эксплуатации, Страница: 70 / 115

Результаты поиска

Содержание 55N3

Отзывы: