IHI 55N3 Скачать руководство пользователя страница 83

Страница: 83 / 115

3 – 13

ᵑ

MAINTENAN

Walk-Around Inspection

Inspect the operator’s compartment for
cleanliness. Keep it clean.

Inspect the loose bolts, Tighten any loose bolts.
Repair if necessary.

Inspect any cracks in boom and arm pivot area
and cylinder mounting brackets.
Repair if damaged.

Inspect attachment cylinders, linkage and bucket
for damage or excessive wear.
Repair if damaged.

Inspect and remove any trash build up in the
engine compartment.

Inspect the cooling system for leaks, faulty hose
and trash built up. Correct any leaks and remove
any trash from the radiator.

Inspect the hydraulic system for leaks. Inspect
the tank, cylinder rod seals, tubes, plugs, joints
and fittings. Correct any leaks.

Inspect and repair travel drive leaks. Check oil
level if leakage is noticed.

Daily Lubrication

Perform the daily lubrication as required by the
Lubrication Chart.

DAILY

Содержание 55N3




















































































































Результаты поиска

Содержание 55N3

Отзывы:

IHI 55N3, Руководство по эксплуатации, Страница: 83 / 115

Результаты поиска

Содержание 55N3

Отзывы: