IHI 55N3 Скачать руководство пользователя страница 45

Страница: 45 / 115

2 – 3

ᵐ

ATI

ELECTRONIC MONITOR PANEL

1. MONITOR LAMPS

Engine Oil Pressure Warning Lamp

When warning lamp comes on and the action alarm
sounds with the engine running, stop the engine.
This indicates insufficient oil pressure.
Check the engine oil level and have any necessary
repairs made before starting the engine.

Charge Warning Lamp

This indicates a malfunction in the electrical charging
system.
If the light comes on while the engine is running,
check the electrical system.

Heat Indicator Lamp

Hold the engine start switch in the

HEAT

position for

approximately 15 seconds. The air heater is
activated and the indicator comes on.

Engine Fail Lamp

The lamp flashes if the engine abnormality occurs
while the engine is running.

(1) Engine Oil Pressure

Warning Lamp

(2) Charge Warning Lamp

(3) Heat Indicate Lamp

(4) Fuel Level Gauge

(5) Water Temperature Gauge

Содержание 55N3




















































































































Результаты поиска

Содержание 55N3

Отзывы:

IHI 55N3, Руководство по эксплуатации, Страница: 45 / 115

Результаты поиска

Содержание 55N3

Отзывы: