HP BL30p - ProLiant - 1 GB RAM Скачать руководство пользователя страница 121 | Manualshive

Страница: 121 / 152

background image

Error messages 121

1786-Slot 1 Drive Array Recovery Needed. Automatic Data Recovery Previously Aborted!...

...The following SCSI drive(s) need Automatic Data Recovery: SCSI Port Y: SCSI ID Z
Select F1 to retry Automatic Data Recovery to drive. Select F2 to continue without starting Automatic Data Recovery.

Audible Beeps

: None

Possible Cause

: System is in Interim Data Recovery Mode and a failed or replacement drive has not yet

been rebuilt. This message is displayed if the

F2

key was pressed during a previous boot or if the

F1

key

was pressed during a previous boot and the system rebooted before the rebuild of the drive completed.

Action

:

•

Perform one of the suggested actions:

•

Press the

F1

key to retry Automatic Data Recovery to the drive. Data will be automatically

restored to drive

X

when a failed drive has been replaced, or to the original drive if it is working

again without errors.

•

Press the

F2

key to continue without recovery of data to the drive. The failed drive will not be

rebuilt and the system will continue to operate in a failed state of Interim Data Recovery Mode.

•

If drive recovery is not successful, run ADU ("

Array Diagnostic Utility

" on page

63

) for more

information.

•

If the replacement drive failed, replace with another drive.

•

If the rebuild was aborted due to a read error from another physical drive in the array, back up
all readable data on the array, run ADU, and then restore the data.

1787-Drive Array Operating in Interim Recovery Mode...

...Physical drive replacement needed: Drive X

Audible Beeps

: None

Possible Cause

: Hard drive

X

failed or cable is loose or defective. Following a system restart, this

message notes that drive

X

is defective and fault tolerance is being used.

Action

:

1.

Be sure all cables are connected properly and securely.

2.

Test and replace defective cables.

3.

Replace drive

X

. (depending on the fault-tolerance level, all data may be lost if another drive fails).

1788-Slot X Drive Array Reports Incorrect Drive Replacement...

...The following SCSI drive(s) should have been replaced: SCSI Port Y: SCSI ID Z.
The following SCSI drive(s) were incorrectly replaced: SCSI Port y: SCSI ID z.
Select F1 to continue – drive array will remain disabled.
Select F2 to reset configuration – all data will be lost.

Audible Beeps

: None

Possible Cause

:

•

Replacement drives may have been installed in the wrong drive bays.

•

A bad power cable connection to the drive, noise on the data cable, or defective SCSI cable exists.

Action

:

•

If replacement drives are installed in the wrong bays, properly reinstall the drives as indicated and:

•

Press the

F1

key to restart the server with the drive array disabled.

•

Press the

F2

key to use the drives as configured and lose all the data on them.

•

If a bad power cable connection exists:

«
...
119
120
121
122
123
...
»

Содержание BL30p - ProLiant - 1 GB RAM

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для BL30p - ProLiant - 1 GB RAM

Бренд: ZyXEL Communications Страницы: 2

Бренд: I-GO Страницы: 2

Бренд: Oakton Страницы: 9

Бренд: HQ Страницы: 20

Бренд: Mesa Страницы: 2

Бренд: AzureWave Страницы: 31

Бренд: R&S Страницы: 66

Бренд: CICH International Страницы: 7

Бренд: VOLTCRAFT Страницы: 4

Бренд: Rosewill Страницы: 12

Бренд: Magnadyne Страницы: 2

Бренд: Transition Networks Страницы: 5

Бренд: 3idee Страницы: 7

Бренд: SPI CORP Страницы: 7

Бренд: Westermo Страницы: 28

CompactFlash CA1040

Бренд: Abocom Страницы: 1

Бренд: Toa Страницы: 1

Бренд: Snom Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды