HP BL30p - ProLiant - 1 GB RAM Скачать руководство пользователя страница 120 | Manualshive

Страница: 120 / 152

background image

Error messages 120

2.

Be sure all drives are fully seated.

3.

Replace defective cables, drive

X

, or both.

1785-Slot X Drive Array Not Configured...

(followed by one of the following):
...(1) Run Array Configuration Utility
(2) No drives detected
(3) Drive positions appear to have changed – Run Drive Array Advanced Diagnostics if previous positions are
unknown. Then turn system power OFF and move drives to their original positions.
(4) Configuration information indicates drive positions beyond the capability of this controller. This may be due to
drive movement from a controller that supports more drives than the current controller.
(5) Configuration information indicates drives were configured on a controller with a newer firmware version.

Audible Beeps

: None

Possible Cause

: Drive array configuration not detected.

Action

:

•

Run ACU ("

Array Configuration Utility

" on page

54

).

•

Power down the system and check SCSI cable connections to be sure the drives are connected
properly.

•

Run ADU ("

Array Diagnostic Utility

" on page

63

) if previous positions are unknown. Then, turn the

system power off and move the drives to their original positions.

•

To avoid data loss, update the controller firmware to the same or later version on the original
controller ("

Firmware maintenance

" on page

65

).

1786-Disk 0 Software RAID Failure, Booting Disk 1

Audible Beeps

: None

Possible Cause

: The operating system has marked the RAID 1 bootable partition on Disk 0 as bad or

the hard drive has failed.

Action

: The system attempts to boot from Disk 1. Perform one of the following actions:

•

Replace the primary drive, if applicable, and re-mirror the data from the secondary drive.

•

Repair the logical drive. Refer to the operating system documentation.

1786-Slot 1 Drive Array Recovery Needed...

...The following SCSI drive(s) need Automatic Data Recovery: SCSI Port Y: SCSI ID Z
Select F1 to continue with recovery of data to drive. Select F2 to continue without recovery of data to drive.

Audible Beeps

: None

Possible Cause

: A failed or replacement drive has not yet been rebuilt.

Action

:

•

Perform one of the following actions:

•

Press the

F1

key to continue with recovery of data to the drive. Data will be automatically

restored to drive

X

when a failed drive has been replaced, or to the original drive if it is working

again without errors.

•

Press the

F2

key to continue without recovery of data to the drive. The failed drive will not be

rebuilt and the system will continue to operate in a failed state of Interim Data Recovery Mode.

•

Replace the failed drive and press the

F1

key to rebuild the array. If the drive rebuild is not

successful or is aborted because the system rebooted before the rebuild of the drive completed,
another version of the 1786 POST error message will be displayed. Refer to the following message.

«
...
118
119
120
121
122
...
»

Содержание BL30p - ProLiant - 1 GB RAM

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для BL30p - ProLiant - 1 GB RAM

Бренд: ZyXEL Communications Страницы: 8

Бренд: Targus Страницы: 103

Бренд: TRENDnet Страницы: 28

Бренд: BeeWi Страницы: 73

SNG 12/1500-OW-N

Бренд: VOLTCRAFT Страницы: 4

Бренд: StarTech.com Страницы: 2

Бренд: Intermec Страницы: 4

Бренд: Tripp Lite Страницы: 12

Бренд: Prudent Way Страницы: 6

Бренд: Dynex Страницы: 13

FriendlyNET Home

Бренд: Asante Страницы: 4

Бренд: Philips Страницы: 2

FoneMate SFA-0001

Бренд: TeleVue Страницы: 2

Бренд: Telex Страницы: 136

Centrino Advanced-N 6200

Бренд: Intel Страницы: 47

Pavilion zt3100 - Notebook PC

Бренд: Compaq Страницы: 2

Бренд: JINOU Страницы: 26

Бренд: Steren Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды