HP BL30p - ProLiant - 1 GB RAM Скачать руководство пользователя страница 116

Страница: 116 / 152

Error messages 116

Expansion will resume when automatic data recovery has been completed.

Audible Beeps

: None

Possible Cause

: The capacity expansion process has been temporarily disabled.

Action

: Follow the action that is displayed onscreen to resume the capacity expansion process.

1753-Slot Z Drive Array - Array Controller Maximum Operating Temperature Exceeded During
Previous Power Up

Audible Beeps

: None

Possible Cause

: Controller is overheating.

Action

: Be sure adequate system cooling and sufficient airflow across controller are available.

1768-Slot X Drive Array - Resuming Logical Drive Expansion Process

Audible Beeps

: None

Possible Cause

: Power was lost while a logical expansion operation was performed. A controller reset

or power cycle occurs while array expansion is in progress.

Action

: No action is required.

1769-Slot X Drive Array - Drive(s) Disabled Due to Failure During Capacity Expansion

...Select F1 to continue with logical drives disabled. Select F2 to accept data loss and to re-enable logical drives.

Audible Beeps

: None

Possible Cause

: Data was lost while the array was expanded; therefore, the drives have been

temporarily disabled. Capacity expansion failed due to:

•

Array accelerator or hard drive failed or was removed; expansion progress data lost

•

Expansion progress data could not be read from array accelerator

•

Expansion aborted due to unrecoverable drive errors

•

Expansion aborted due to array accelerator errors

Action

•

Press the

key to accept the data loss and re-enable the logical drives.

•

Restore data from backup.

•

Replace drive or array accelerator, as appropriate.

1770-Slot X Drive Array - SCSI Drive Firmware Update Recommended - ...

...Please upgrade firmware on the following drive(s) using ROM Flash Components (download from
www.hp.com/support/proliantstorage): Model XYZ (minimum version = ####)

Audible Beeps

: None

Possible Cause

: Drive firmware update needed.

Action

: The indicated drives are running firmware that is known to cause intermittent problems. Update

all drives to the latest firmware version ("

Firmware maintenance

" on page

Содержание BL30p - ProLiant - 1 GB RAM

























































































































































Результаты поиска

Содержание BL30p - ProLiant - 1 GB RAM

Отзывы:

Похожие инструкции для BL30p - ProLiant - 1 GB RAM

Бренды по названию

Популярные бренды

HP BL30p - ProLiant - 1 GB RAM, Руководство по устранению неисправностей

Результаты поиска

Содержание BL30p - ProLiant - 1 GB RAM

Отзывы:

Похожие инструкции для BL30p - ProLiant - 1 GB RAM

Бренды по названию

Популярные бренды