Hologic DISCOVERY A Скачать руководство пользователя страница 254 | Manualshive

Страница: 254 / 274

background image

A-8

C-Arm

Comment: Attempt to turn on X-rays when either the filter drum is not yet locked (if it
is on) or the initial 30-second X-ray delay after startup has not elapsed. Reported as the
device state if the C-arm is reset. Reported as command error for any IS_xxx command
executed from an application (as opposed to executing from a state machine).

Action: Wait until the filter drum synchronizes to the A/C line and until the high
voltage relay in the X-ray controller is turned on (30 seconds after the system starts).

Motor_xx

Reported as command error for any IS_xxx command executed from an application (as
opposed to executing from a state machine). Reported as device state if the motor is
reset.

Action: Determine why the motor was reset (e.g., power line brown out).

Motor_TZ

Reported as command error for any move command until valid calibration information
has been downloaded. Reported as command error for any IS_xxx command executed
from an application (as opposed to executing from a state machine).

Action: Verify that the TZ driver has been calibrated and that the correct Hologic
system startup procedure has been followed (i.e., reboot the system and if the problem
persists, recalibrate the TZ motor)

Device time-out waiting for requested action [E_TIME_OUT_I]

Comment: For everything except the state machine, indicates that a message was sent
to the device and a response was not received within 150ms.

Action: Follow the procedure under "BAD CHECKSUM IN MESSAGE." for isolating
the failed device and replace or repair it.

Comment: For the state machine, indicates that one of the self-limiting commands has
timed out or that the state machine continued executing into the next cycle.

Action: Report this error to Hologic Technical Support.

ERROR MESSAGE

HARDWARE

/SOFTWARE

ERROR

LOCUS

COMMENT/ACTION

«
...
252
253
254
255
256
...
»

Содержание DISCOVERY A



















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DISCOVERY A

Бренд: JB-Lighting Страницы: 60

Бренд: Cambro Страницы: 6

Бренд: Patlite Страницы: 28

Web Ankle Brace

Бренд: Darco Страницы: 2

Бренд: Darkly Labs Страницы: 13

Бренд: DARAY Страницы: 24

Body Armor Night Splint

Бренд: Darco Страницы: 2

Бренд: LaboGene Страницы: 59

Бренд: Water Witch Страницы: 2

Бренд: Falltech Страницы: 48

Бренд: jablotron Страницы: 2

Бренд: jablotron Страницы: 2

Бренд: Landoll Страницы: 144

Бренд: Castellini Страницы: 299

Бренд: Lowenstein Medical Страницы: 457

GrainLogix XLB10

Бренд: LOFTNESS Страницы: 104

Бренд: Strapack Страницы: 16

Бренд: Hameg Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды