Hologic DISCOVERY A Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 274

background image

Discovery QDR Series Technical Manual

3-56

processes pointing towards the head end of the table. The laser crosshair should
be 1.5 inch in from the left end and centered. (Some phantoms will have a target
hole, if not, use a ruler).

If you are using a DXA Quality Control Phantom (aluminum representation of
vertebral bodies that does not resemble real bone, Part Number ASY-01564),
place the phantom on end with the flattening target facing up. Orient the phantom
so the metal edge is to the right (head end) and tissue to the left (foot end) as
viewed from the front of the table. Align the phantom flattening target to the laser
crosshair.

3. Start the X-Ray Survey Utility by selecting Utilities/Service Utilities/X-Ray

Survey (see “X-Ray Survey” on page 9-1 for information on the utility).

4. Set Pulse to 1, High gain to 2, Low gain to 1, X-ray Mode to 3 and Aperture to

7.

5. For Display, click Graph.

6. Click X-Rays (F2) to turn X-Rays on.

7. Check that phantom covers the whole beam. This is critical. If phantom does not

cover the whole beam, move it until it does. Keep the phantom as straight as pos-
sible.

8. Turn off X-rays with the

<F2>

key and press

<Esc>

to exit X-Ray Survey.

Reboot the PC, logon as Field Service, and restart the software in Service Mode
to return to Discovery Main Menu screen.

9. Select

Utilities|Service Utilities|Detector Flattening

. Click the Continue

button. This procedure can takes about 10 minutes on a C or W model and 55
minutes on an A or SL.

10. When flattening is complete, run a QC scan and cancel adding it to the QC plot.

11. Use the Scan File Plot utility to check X-ray beam flatness of the QC scan per-

formed in Step 10.

3.5.4 Perform Lateral Alignment Test (A and SL)

Note: This procedure applies to A and SL systems only. Use this procedure to verify

lateral alignment.

This procedure verifies lateral alignment.

1. On the control panel press Center to move the table and C-Arm to the center

position.

2. On the control panel press Laser on the control panel to turn the laser light on.

3. Place the spine phantom on the table top with its laser target towards the left (foot

end) and the vertebrae to the right (head end).

WARNING:

X-rays are generated during this procedure. Keep hands, head and other body parts out
of beam.

«
...
106
107
108
109
110
...
»

Содержание DISCOVERY A



















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DISCOVERY A

Бренд: MacDon Страницы: 272

Бренд: MacDon Страницы: 70

Бренд: Parr Instrument Страницы: 24

Бренд: JBL Страницы: 15

Бренд: idiag Страницы: 12

Бренд: GALBIATI Страницы: 20

Бренд: CAMAG Страницы: 40

Бренд: EASTERN INSTRUMENTS Страницы: 93

Бренд: Pari Страницы: 2

Бренд: Landoll Страницы: 70

Бренд: Landice Страницы: 19

Бренд: Landice Страницы: 7

Бренд: PASCO Страницы: 5

Бренд: Pasco Scientific Страницы: 27

Бренд: PARUS Страницы: 6

LED Street Bar 16x3W RGB IP65

Бренд: Varytec Страницы: 9

Бренд: VARILITE Страницы: 8

EVENTPROFILE VL800

Бренд: Vari Lite Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды