Hologic DISCOVERY A Скачать руководство пользователя страница 184

Страница: 184 / 274

Discovery QDR Series Technical Manual

5-18

5.6.2 X-Ray Controller Assembly

To remove and replace the X-Ray Controller (XRC), refer to Figure 5-22 and do the
following:

1. Using the Control Panel, move the table in for easier access to the XRC.

2. Shut down the computer and then turn off the main circuit breaker on the foot end

pedestal.

3. Remove the lower C-arm cover by removing 2 Phillips screws and sliding it out

from the front.

4. Remove the 4 Phillips screws holding the XRC (see Figure 5-7

5. Pull the XRC forward far enough to access the cables.

6. Unplug all of the cables and remove the XRC by pulling it out.

7. To replace the XRC reverse the steps.

8. Restore power, boot the computer and login as Service.

9. Perform “Area, BMD, and BMC Calibration” on page 4-34.

10. Log out of Service and login as User.

11. Perform “Test Scan Modes” on page 3-64.

5.6.3 Filter Drum Assembly

To remove and replace the Filter Drum Assembly, refer to Figure 5-7 and do the
following:

1. Using the Control Panel, move the table in as far as it will go and center the C-

arm for easier access to the Filter Drum Assembly.

2. Start the X-Ray Survey Utility by selecting Utilities|Service Utilities|X-Ray

Survey (see “X-Ray Survey” on page 9-1 for information on the utility).

3. Set Aperture to 7.

4. Shut down the computer and then turn off the main circuit breaker on the foot end

pedestal.

5. Remove the lower C-arm cover by removing 2 Phillips screws and sliding it out

from the front. Also, remove the bottom cover.

6. Remove the 4 Phillips screws holding the XRC (see Figure 5-7).

7. Pull the XRC forward far enough for access to the Filter Drum (it is not neces-

sary to remove the XRC cables.

8. Remove the rear tank cover (covers the C-arm Interface board).

9. Unplug the 2 Filter Drum cables from the C-arm Interface board.

10. Remove 3 hex head screws (3/32 inch Allen screws).

Содержание DISCOVERY A



















































































































































































































































































Результаты поиска

Содержание DISCOVERY A

Отзывы:

Похожие инструкции для DISCOVERY A

Бренды по названию

Популярные бренды

Hologic DISCOVERY A, Техническое руководство

Результаты поиска

Содержание DISCOVERY A

Отзывы:

Похожие инструкции для DISCOVERY A

Бренды по названию

Популярные бренды