Hologic DISCOVERY A Скачать руководство пользователя страница 252 | Manualshive

Страница: 252 / 274

background image

A-6

STATE

Comments:
1. An application attempted to load or execute a state machine when one was already

running, or an application attempted to execute a state machine while one or more
devices were still executing a command, or an attempt to abort the currently
executing state machine failed.

2. Whenever an application issues a device command and the state machine is

executing a state machine protocol.

Action: Report these errors to Hologic Technical Support.

MOTOR_xx

Comment: An application attempted to modify stepper motor parameters while the
motor was moving (acceleration distance/type, first/final rates, position average, etc.),
or an application issued a MOVE_ABS while a MOVE_REL was in progress (or vice
versa).

Action: Report this error to Hologic Technical Support.

C-Arm

Comments:
1. An application attempted to control the laser positioning light when it was under

local control or an application attempted to turn on the laser while the C-arm and
table were within the laser safety distance of each other.

Action: Be sure the table and C-arm are properly positioned before starting a scan.
If the problem persists, report this error to Hologic Technical Support.

2. An application attempted to issue another move command to the aperture shuttle

while it was still moving.

Action: The aperture may not be calibrated and an application attempted to move it
to a calibrated position. The aperture shuttle on the C-arm may be jammed and the
driver is still attempting to position it in response to a previous MOVE_ABS
command. Visually inspect the aperture shuttle and use the MOVE_REL command
to verify that the shuttle is moving. If it is not, fix the mechanical or electrical
problem with the aperture shuttle and then recalibrate the aperture.

ERROR MESSAGE

HARDWARE

/SOFTWARE

ERROR

LOCUS

COMMENT/ACTION

«
...
250
251
252
253
254
...
»

Содержание DISCOVERY A



















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DISCOVERY A

Бренд: ZOLL Страницы: 84

Бренд: Kaivac Страницы: 29

Бренд: MacDon Страницы: 65

Бренд: Raytheon Страницы: 68

Бренд: KegLand Страницы: 23

Бренд: Safavieh Страницы: 2

Бренд: Vendlet Страницы: 2

Бренд: Tactile Medical Страницы: 23

Бренд: Taarup Страницы: 72

KONTROL KUBE ABACUS

Бренд: FIBERLOCK Страницы: 8

Бренд: Monosem Страницы: 92

Бренд: Otto Bock Страницы: 252

Бренд: Original BTC Страницы: 2

Бренд: ResMed Страницы: 8

Бренд: Osprey Страницы: 12

DIAGNOdent pen 2190

Бренд: KaVo Страницы: 2

Бренд: Glow Bricks Страницы: 9

Бренд: KYORITSU Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды