Hologic DISCOVERY A Скачать руководство пользователя страница 272 | Manualshive

Страница: 272 / 274

background image

A-26

Unexpected message from remote device [E_UNEXPECTED_RESPONSE_I]

Comment: The first character in a fast query response was not the fast query command
("?").

Action: Follow the procedure under "BAD CHECKSUM IN MESSAGE." for isolating
communications bus I/O errors.

Unknown ROI type in DrawROI

Software

These messages should be reported to Hologic Technical Support. Include as much
information as possible about what you were doing at the time.

device: Unrecognized Command Code

Software

This message should be reported to Hologic Technical Support. Include as much
information as possible about what you were doing at the time.

Unrecognized device command [E_UNKNOWN_COMMAND_I]

Comment: Returned by all devices in response to an unrecognized command.

Action: Report this error to Hologic Technical Support. Include as much information as
possible about what you were doing at the time.

Unsolicited message from C/C [E_UNSOLICITED_MESSAGE_I]

Action: Report this error to Hologic Technical Support. Include as much information as
possible about what you were doing at the time.

X-ray controller is not generating A/C line interrupts [E_NO_TIMER_INTERRUPT_I]

DAS

Global

A request was made to read the a/d's and there was no system line frequency interrupts
(required to synchronize DAS with C-arm).

The system was on-line and another on-line command was issued but there were still
no timer interrupts.

Action: Check that the Instrument Power switch and the X-Ray Enable key are on.
Also, see the discussion of E_INTERLOCK_INHIBIT_I, E_EMERGENCY_STOP_I
and E_COLLISION_IMMINENT_I.

Refer to the “NO A/C Line Interrupts” message at start-up on page 6-9.

ERROR MESSAGE

HARDWARE

/SOFTWARE

ERROR

LOCUS

COMMENT/ACTION

«
...
270
271
272
273
274
»

Содержание DISCOVERY A



















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DISCOVERY A

LOUDEN 200 Series

Бренд: ACCO Brands Страницы: 144

Бренд: B&K Страницы: 16

Бренд: B&G Страницы: 2

Бренд: Tascam Страницы: 8

Бренд: B-K lighting Страницы: 5

Бренд: B-K lighting Страницы: 4

Бренд: B-K lighting Страницы: 3

Бренд: BACtrack Страницы: 16

Бренд: Parker Страницы: 39

Бренд: Hacker Страницы: 2

Бренд: J.P. SELECTA Страницы: 8

Бренд: Haemonetics Страницы: 134

Бренд: Hadeco Страницы: 72

Бренд: Tascam Страницы: 8

EVENTWASH VL800

Бренд: Vari Lite Страницы: 23

Бренд: Vapotherm Страницы: 15

Бренд: Gaspardo Страницы: 88

Бренд: A.J.Antunes Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды