Hologic DISCOVERY A Скачать руководство пользователя страница 250 | Manualshive

Страница: 250 / 274

background image

A-4

Bad checksum in message. [E_BAD_BLOCK_I]

Comment: The checksum calculated by the C/C for a message did not match the one in
the message packet.

Action: Either the driver is incorrectly configured, one or more devices are jumpered to
the debug mode, there is a hardware problem on the communication link (cable or
connectors) or one of more of the DSP chips in the C/C or DAS board is not properly
seated. Verify that the DEVICE=C:\MENU\MAPIDEV.SYS line in CONFIG.SYS has
the options /OVERLAP=0 and /HANDSHAKE=1. Check each stepper motor board
and verify that its address is correctly set. Verify that the TZ motor board does not
have the debug jumper installed. Verify that the communications cable is installed and
properly secured on the back of the C/C board. If the problem persists, it may be
because one (or both) of the DSP chips on the C/C or DAS board is not properly seated
in the PGA socket. Try "massaging" the DSP chip on the C/C board and the one on the
DAS board. If the problem changes (gets worse or better) when you do so, replace the
appropriate board. If the problem persists, place all devices in emulation mode (e.g., by
turning off instrument power and booting in the workstation mode). Disconnect all
devices except the C-arm from the communications link. Turn off C-arm emulation. If
there are no problems, proceed to re-connect each device and take it out of emulation
until the offending device is found. Replace the appropriate board.

BoundaryLine Internal Software Error

Software

This message should be reported to Hologic Technical Support. Include as much
information as possible about what you were doing at the time.

Cannot generate bad detector map, too many bad detectors

Action: One or more detectors is bad. See instructions for running hardware checking
program.

Cannot obtain results of scan ________ of __________

Software

Comment: For some reason, the system was unable to obtain the results of a scan that
was selected for normals plotting.

Action: This message should be reported to Hologic Technical Support.

Can't open a window

Software

Action: Ensure that only Hologic software is installed on the computer. If so, report
this message to Hologic Technical Support. Include as much information as possible
about what you were doing at the time.

ERROR MESSAGE

HARDWARE

/SOFTWARE

ERROR

LOCUS

COMMENT/ACTION

«
...
248
249
250
251
252
...
»

Содержание DISCOVERY A



















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DISCOVERY A

Бренд: York Fitness Страницы: 34

Бренд: Badger Meter Страницы: 16

Бренд: Xiitech Страницы: 6

Бренд: MacDon Страницы: 46

Бренд: MacDon Страницы: 82

Бренд: Mac Medical Страницы: 2

Бренд: MACDEV Страницы: 8

Mentor Touch ET750

Бренд: MAC TOOLS Страницы: 24

Бренд: MA lighting Страницы: 10

ThermoTweez Handpiece TT-65

Бренд: Pace Страницы: 14

Бренд: Posture Pump Страницы: 2

Бренд: Phenix Technologies Страницы: 39

Бренд: Triton Страницы: 31

PulseDose LT PD1000

Бренд: DeVilbiss Страницы: 58

Wallach UltraFreeze

Бренд: Cooper Surgical Страницы: 4

Бренд: Carbatec Страницы: 29

Бренд: PurAthletics Страницы: 2

Бренд: Stone Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды