Hologic DISCOVERY A Скачать руководство пользователя страница 261 | Manualshive

Страница: 261 / 274

background image

A-15

State

Comment: Returned as the device state if the C-arm microprocessor returned an
unrecognized response to the fast query.

Action: This may be due to a communications error between the AT and the C-arm.
Follow the procedure under "BAD CHECKSUM IN MESSAGE." to diagnose I/O
errors. Otherwise, report this error to Hologic Technical Support.

Comment: For the state machine driver, this error indicates that either the protocol
attempted to execute a command that is not supported; that an instruction that requires
a register reference did not provide one; or, more commonly, an attempt was made to
access the external data buffers and they were either not available or were still being
using by the application.

Action: If you are running any program other than standard Hologic software, remove
it and retry the scan (e.g., do not run a scan while connected to a network or attempt to
run a scan under Windows). Otherwise, report this error to Hologic Technical Support.

Motor_xx

Comment: For a stepper motor, the application attempted to move a motor in the
opposite direction in which it is currently moving (i.e., a motor's motion can be
extended in the same direction as the current motion but it cannot reverse motion).

Action: Report this error to Hologic Technical Support.

Invalid parameter(s) [E_INVALID_PARAM_I]

Comment: The value of the parameter associated with a device command was out of
range.

Action: Report the application in error to Hologic Technical Support.

Invalid serial number in ARRC.TXT.

Action: This is not an error if the machine is not yet calibrated.

Invalid serial number in environ.bat file.

Action: Machine serial number is not valid. Call Hologic Technical Support.

Invalid values in bad detector map

Action: See instructions for running hardware checking program.

ERROR MESSAGE

HARDWARE

/SOFTWARE

ERROR

LOCUS

COMMENT/ACTION

«
...
259
260
261
262
263
...
»

Содержание DISCOVERY A



















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DISCOVERY A

Бренд: M-system Страницы: 2

Бренд: Rico Страницы: 34

Бренд: Balanced Body Страницы: 4

Бренд: Balanced Body Страницы: 2

Reformer Trapeze Combination

Бренд: Balanced Body Страницы: 164

Бренд: Wacker Neuson Страницы: 50

Бренд: Balanced Body Страницы: 37

Бренд: Fagor Страницы: 12

Бренд: Baltic Страницы: 68

Бренд: H&S Страницы: 76

Бренд: Tieline Страницы: 359

Бренд: SAC Страницы: 2

Бренд: GE Страницы: 2

UG 2200 Special

Бренд: Amazone Страницы: 252

Бренд: HOFFEN Страницы: 22

Бренд: KEP Страницы: 33

BOMAG BW 120 AD-5

Бренд: Fayat Страницы: 210

Levitator III F-LHLEV3

Бренд: Skytron Страницы: 248

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды