manualshive.com logo in svg

Hioki IM7580, Инструкция по эксплуатации

Поделиться
Скачать
Hioki IM7580 Скачать руководство пользователя страница 81

73

Setting Basic Settings of Measurement

The numeric keypad can be 

used for input.

Wait time

INDEX time

6

8

7

6 

 Use 

/

 or the numeric keypad to set the 

wait time (time to stabilize) from the time a 

measurement signal has been output by applying 

a trigger to the start of next measurement.

(With the numeric keypad, press 

[SET]

.)

Settable range 0.00000 s to 9.99999 s

[C]

Sets to the default value.  

(The time is set to 0.001 s.)

7 

 Set the 

INDEX delay

 time.

(With the numeric keypad, press 

[SET]

.)

Settable range 0.00000 s to 0.10000 s

8 

 Press 

[EXIT]

 to close the trigger synchronous 

output setting screen.

9 

 Press 

[EXIT]

 to close the setting screen.

 

• When the trigger synchronous output function is set to 

[ON]

, the measurement time will increase due 

to the incorporation of a wait time between output of the measurement signal and data acquisition.  

See “12.3 Measurement Time” (p. 290).

 

• When the trigger synchronous output function is set to 

[ON]

, the set level may be output momentarily 

if a measurement condition is changed.

 

•

The measurement signal is output when the trigger signal is input and stops after measurement ends.

 

•

In CONTINUOUS measurement mode, the initial pulse is set after measurement of the last panel 

ends.  

If the trigger synchronous function is set to 

[ON]

 for the initial panel, the measurement signal stops.

4

Analyzer Function

Содержание IM7580





















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды