Hioki IM7580 Скачать руководство пользователя страница 324

Страница: 324 / 340

Rack Mounting

Slide the unit into the rack from the front of the

rack mounting plate.

Screw (M3 × 10 mm)

Use the screws removed from

the legs (M3 × 10 mm) and the

corresponding screw holes to

fasten the instrument.

(For example, place the instrument on

a storage rack and fasten it from the

back of the rack with screws.)

If the plate thickness of the storage

rack exceeds 4 mm, use screws with

a length that allows the screws to be

inserted to a depth of 6 mm to 10 mm

from the bottom to the interior of this

instrument (M3 × Plate thi

6 mm to 10 mm).

Содержание IM7580





















































































































































































































































































































































Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды

Hioki IM7580, Инструкция по эксплуатации

Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды