Hioki IM7580 Скачать руководство пользователя страница 311

Страница: 311 / 340

303

Error Display

13.4 Error Display

If any of the following are displayed on the screen, check the corresponding reference page.

Error display

Description

Solution/Reference

REF VAL

Measurement value is outside the

guaranteed accuracy range.

Check the measuring range. (p. 274)

MEAS ERR

Measurement error.

Check if the measurement cable has been

disconnected or connected incorrectly.

If an error is still displayed, the instrument

may be damaged.

Contact your authorized Hioki distributor or

reseller.

DISP OUT

Measurement value is outside the

display range.

Check the display range.

“Display range” (p. 273)

Hi Z

The measurement result is higher

than the judgment reference set for

the Hi Z reject function.

Check the connection.

“Detecting OPEN During 2-terminal

Measurement (HIGH-Z Reject Function)”

(p. 174)

LEV ERR

This is displayed when abnormal

detection level is detected while

detection level monitoring function

is enabled.

Check the connection.

“Monitoring the Detection Level (Detection

Level Monitoring Function)” (p. 175)

MEMORY FULL

This is displayed when the set

number of measurement results

have been stored in the instrument

memory.

Load measurement values stored in the

instrument memory with the memory function

or clear the memory.

“Saving Measurement Results (Memory

Function)” (p. 180)

The internal temperature has

exceeded the operating range or

the cooling fan has stopped.

Switch OFF the power supply at once.

Check the installation environment of the

instrument.

Check the condition of the instrument’s

cooling fan. There is a possibility of failure.

Contact your authorized Hioki distributor or

reseller.

ERROR

The current consumption of the front

USB terminal exceeds 500 mA.

Use a different type of USB flash drive.

Format of the USB flash drive is not

compatible with this instrument.

Use a different type of USB flash drive or

backup existing files in the USB flash drive

and format the drive before use.

File format error.

File cannot be loaded.

•

File is damaged.

•

File is not supported by this

instrument.

Check if file is corrupted or USB flash drive is

damaged.

Media space error.

USB flash drive does not sufficient

free memory space.

Use a different USB flash drive or increase

free space.

Maintenance and Service

Содержание IM7580





















































































































































































































































































































































Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды

Hioki IM7580, Инструкция по эксплуатации

Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды