Hioki IM7580 Скачать руководство пользователя страница 286

Страница: 286 / 340

278

General Specifications

(4) Continuous measurement function

Measurements are continued with measurement conditions saved.

1. Up to 46 ways

LCR mode: Up to 30 ways, ANALYZER mode: Up to 16 ways

Continuous measurements with LCR mode mixed with ANALYZER mode is possible

Judgment result from EXT.I/O has an overall judgment result and more than one output pattern.

(5) Function

Contact check

2-terminal contact check (DCR measurement)

Performs a contact (contact state) check between High and Low.

Judgment is allowed by entering upper and lower limit for DCR values.

A function that aborts subsequent measurements when the judgment result is FAIL available.

Check timing can be changed.

BEFORE: Contact check performed before measurement

AFTER: Contact check performed after measurement

BOTH: Contact checks performed before and after measurement

Measurement

a. Range 0.1

to 100

b. ±1.6% rdg. (typical)

Measurement signal

Level: 1 mA or less
Number of waveforms: 1 to 9,999 (8 µs to 79992 µs)

Wait time

Wait before DC measurement: 0 s to 9.99999 s
Wait before AC measurement: 0 s to 9.99999 s

AC signal superimpose available

Hi-Z reject function (detection of OPEN state during 2-terminal measurement)

When the measurement value is higher than the judgment reference, a contact error is

output.

Judgment standard: Setting 1

to 10 k

(resolution: 1

) available

Error output: Error output from EXT I/O

Waveform identification function (chattering detection)

Effective values of subsequent waveforms is compared with the effective value of the

waveform that is read first. A contact error is output if fluctuation of the subsequent waveform

exceeds the judgment reference.

Judgment reference: Setting 0.01% to 100.00% (0.01% resolution) with respect to the

reference value is possible.

Error output: Error is displayed on the LCD display and error is output from EXT I/O

Panel save

and load

function

Full measurement condition: Saving 30 types (LCR mode) and 16 types (ANALYZER mode) of

setting conditions are possible.

Compensation value only: Saving 30 types (LCR mode) of compensation values are possible.

Arbitrary measurement conditions can be read by key operations or a control signal via the EXT I/

Display

digits setting

function

Number of display digits for measurement values can be set to 3, 4, 5, and 6. However, differs

based on the parameter. (default: 6 digits)

Display

Setting

function

1. LCD display ON/OFF (no drawing in case of OFF)

Back light brightness adjustment

3. Measurement screen color customization (color with white background or black background)

Содержание IM7580





















































































































































































































































































































































Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды

Hioki IM7580, Инструкция по эксплуатации

Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды