Hioki IM7580 Скачать руководство пользователя страница 255

Страница: 255 / 340

247

Saving Data to USB Flash Drive

FILE_USB_SAVE.png

Press

[SAVE]

in the measurement screen.

Measurement data is saved in the USB flash drive.

•

Auto save (default): Measurement data is saved.

•

For manual save: See “Setting Save Folder” (p. 256).

• Auto save (default setting) automatically creates a folder in the USB flash drive and saves the

file in the folder.

The folder name is created with the date and time of saving.

Example: Saved on July 30, 2014 -> 20140730

•

For manual save: See “11.4.3 Setting Save Folder” (p. 256).

• Name of the file is automatically assigned from the date and time for both auto save and

manual save modes.

Example: Saved at 16:31:44 on July 30, 2014 -> 140730163144.csv

Using

USB
Flash

Drive

Содержание IM7580





















































































































































































































































































































































Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды

Hioki IM7580, Инструкция по эксплуатации

Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды