Hioki IM7580 Скачать руководство пользователя страница 250

Страница: 250 / 340

242

Screen Display When Using USB

11.3 Screen Display When Using USB

The display is as follows when a USB flash drive is being used.

You can configure settings such as save format, save destination, and text save format for the files.

Screen

File name

File size

File save date and time

You can check the usage rate and type of file

system of the USB flash drive.

Filesystem

File system type

All

Total size

Used

Space used

Avail

Free space

You can change the sorting order of files.

The number of

and

signs shows the sorting

priority.

Extension will be given priority for the sorting

order of files with

EXT

Allows advanced setting for file save.

Содержание IM7580





















































































































































































































































































































































Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды

Hioki IM7580, Инструкция по эксплуатации

Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды