manualshive.com logo in svg

Hioki IM7580, Инструкция по эксплуатации

Поделиться
Скачать
Hioki IM7580 Скачать руководство пользователя страница 191

183

Common Functions (LCR Mode, ANALYZER Mode)

Setting the background color

1

2

3

1 

 Press 

[SETUP]

.

2 

 Press 

[COMMON]

 tab.

(Press 

[ADVANCED]

 tab for the ANALYZER mode)

3 

 Press 

[DISP]

.

4

5

6

4 

 Press 

[COLOR]

.

5 

 Setting the background color.

[BLACK]

Sets the background color of the screen to 

black.

[WHITE]

Sets the background color of the screen to 

white.

The parameter colors will be initialized in accordance 
with the background color when the background color is 
changed.

6 

 Press 

[EXIT]

 to close the setting screen.

Setting the screen brightness

1

2

3

1 

 Press 

[SETUP]

.

2 

 Press 

[COMMON]

 tab.

Press 

[ADVANCED]

 tab for the ANALYZER mode.

3 

 Press 

[DISP]

.

4

5

4 

 Set the screen brightness with 

/

.

Settable range 0 to 250 (Default value: 130)

5 

 Press 

[EXIT]

 to close the setting screen.

7

Application Function

Содержание IM7580





















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды