Hioki IM7580 Скачать руководство пользователя страница 156

Страница: 156 / 340

148

Calibration

Perform measurement

Performs the calibration measurement.

To avoid improper connection of the standard units, perform “Prevention of improper standard unit

connection” (p. 150) setting in advance.

Open measurement

Connects the standard unit for open to the test

sample connection terminal.

Press

[OPEN]

Press

[AC + DC]

Starts measurement.

If the standard unit used in AC measurement is

different from that the one used in DC measurement,

press

[AC]

[DC]

The results are displayed under

[OPEN]

after

completion of measurement.

[CANCEL]

Cancels the setting, and closes the screen.

Short measurement

Connect the standard unit for short to the test

sample connection terminal.

Press

[SHORT]

Содержание IM7580





















































































































































































































































































































































Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды

Hioki IM7580, Инструкция по эксплуатации

Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды