FujiFilm FM-DP L, Руководство по обслуживанию, Страница: 99 / 380

H3-56
006-252-04 03.22.00 FM2742
FM-DP L
Service Manual
H3-56
MAINTENANCE 3. TROUBLESHOOTING
Error code Error name Significance Probable cause and remedy
Detailed
information format
1268
SC1 discharge error
Attempted to discharge from the before-
sub-scanning conveyor during before-
sub-scanning conveyance, but SC1 did
not detect the trailing edge (OPEN) of
the film.
The following motor/sensor/part may be faulty. Correct
according to the troubleshooting procedure for this error code
in "3.1.4 Troubleshooting Flow".
SC1/MC1/FFM/MD2/MC2/MC3
2-1-A
2-2-A
1271
SD1 supply error
Attempted to convey to the sub
scanning unit during recording
conveyance, but SD1 did not detect the
leading edge. The following motor/sensor/part may be faulty. Correct
according to the troubleshooting procedure for this error code
in "3.1.4 Troubleshooting Flow".
MC1/FFM/MD2/MC2/MC3/SCN board
2-1-C
2-2-A
1275
SE3 supply error
Attempted to supply to the transport unit
during transport unit conveyance, but
the film leading edge (CLOSE) was not
detected at the transport unit exit (SE3). The following motor/sensor/part may be faulty. Correct
according to the troubleshooting procedure for this error code
in "3.1.4 Troubleshooting Flow".
SE3/ME2/FFM/MD2/ME1
2-1-C
2-2-A
1276
SE3 discharge error
Attempted to discharge from the
transport unit during transport unit
conveyance, but the film trailing edge
(OPEN) was not detected at the
transport unit exit (SE3).
The following motor/sensor/part may be faulty. Correct
according to the troubleshooting procedure for this error code
in "3.1.4 Troubleshooting Flow".
SE3/ME2/MG1
2-1-C
2-2-A
1278
SG1 supply error
Attempted to supply to the density
measurement unit during heat
development conveyance, but the film
leading edge (CLOSE) was not detected
at the density measurement unit entrance
(SG1).
The following motor/sensor/part may be faulty. Correct
according to the troubleshooting procedure for this error code
in "3.1.4 Troubleshooting Flow".
SG1/ME2/MG1
2-1-C
2-2-A
1279
SG2 discharge error
Attempted to discharge from the density
measurement unit during heat
development conveyance, but the film
trailing edge (OPEN) was not detected at
the density measurement unit exit (SG2).
The following motor/sensor/part may be faulty. Correct
according to the troubleshooting procedure for this error code
in "3.1.4 Troubleshooting Flow".
SG2/MG1
2-1-C
2-2-A
1286
FFM rotation
inconsistency error
Rotation inconsistency occurred after a
certain period of time after the FFM
started rotating during recording or
initialization remainder
detection/discharge.
The following motor/sensor/part may be faulty. Correct
according to the troubleshooting procedure for this error code
in "3.1.4 Troubleshooting Flow".
FFM/DRV board
2-1-F
1294
No shutter error when
tray 1 tray open The shutter was not inserted when tray 1
was opened with film remaining inside.
After inserting the shutter to tray 1, open the tray. 2-1-A
1295
No shutter error when
tray 2 tray open The shutter was not inserted when tray 2
was opened with film remaining inside.
After inserting the shutter to tray 2, open the tray. 2-1-B