Fiat Punto 2004 Скачать руководство пользователя страница 109

Страница: 109 / 533

1.3 MULTIJET 16V

(75 & 90 HP)

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

pump found in the tank module. The high-pressure pump volume flow rate is distributed as

follows:

approximately 22% is injected by the injectors and burnt in the cylinder;

approximately 28% is used to lubricate the high-pressure pump and is recovered through the

KUEV valve;

approximately 50% corresponds to the excess fuel recovered through the pressure

accumulator and the injectors.

KUEV valve

The purpose of this mechanic valve is to keep the pressure inside the pump constant (it

discharges any overpressure, to prevent pressure peaks from damaging the pump), and also

control the fuel flow needed to cool and lubricate the eccentric shaft and the plungers of the

CP1-H.

FIAT PUNTO

109 / 532

Содержание Punto 2004

































































































































































































































































































































































































































































































































Результаты поиска

Содержание Punto 2004

Отзывы:

Похожие инструкции для Punto 2004

Бренды по названию

Популярные бренды

Fiat Punto 2004, Руководство по обучению

Результаты поиска

Содержание Punto 2004

Отзывы:

Похожие инструкции для Punto 2004

Бренды по названию

Популярные бренды