Fiat Punto 2004 Скачать руководство пользователя страница 487

Страница: 487 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

Bulb replacement:

open the rear hatch, remove rubber caps

, press on elements

and

take transparent glass

out, disconnect the connector, act on fins

in an opposing way to

remove the bulb holder, then take out the force-fitted bulbs and replace the same.

NOTE. Take care of the wiping nozzle tube.

Rear fog lights/reversing lights

These lights are housed onto the rear bumper. Left-hand rear fog light P21W bulb

, right-

hand reversing light P21W bulb

(for left-hand drive versions). Reverse arrangement for

right-hand drive versions. Built-in reflector.

Bulb replacement:

disconnect, from under the bumper, the connector, then take the bulb

holder off. The lights shall not be removed from the bumper.

License plate lights

gb Fiat Grande Punto OK

486 / 532

Two lights with W5W bulbs, housed onto the rear bumper. Optimum homogeneity of light

distribution, which allows the license plate to be clearly seen.

Содержание Punto 2004

































































































































































































































































































































































































































































































































Результаты поиска

Содержание Punto 2004

Отзывы:

Похожие инструкции для Punto 2004

Бренды по названию

Популярные бренды

Fiat Punto 2004, Руководство по обучению

Результаты поиска

Содержание Punto 2004

Отзывы:

Похожие инструкции для Punto 2004

Бренды по названию

Популярные бренды