Fiat Punto 2004 Скачать руководство пользователя страница 464

Страница: 464 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

Boot

If the “independent driver’s door unlocking” option is active, the boot will not be unlocked (the

customer has requested that the vehicle can be accessed only through the driver’s door).

The boot is always independent with respect to the door status, and can be opened only by

means of a special control.

In the event that the battery does not deliver enough power for the electric door lock/handle

function, the boot can in any case be unlocked and opened by actuating a special lever that

can be reached by removing a mask located on the luggage board. No latch is found on the

boot. The boot can also be opened from the inside (in case of electric system malfunction) by

means of a mechanic safety device that can be actuated through a mask located in the upper

portion of the luggage board.

gb Fiat Grande Punto OK

463 / 532

Содержание Punto 2004

































































































































































































































































































































































































































































































































Результаты поиска

Содержание Punto 2004

Отзывы:

Похожие инструкции для Punto 2004

Бренды по названию

Популярные бренды

Fiat Punto 2004, Руководство по обучению

Результаты поиска

Содержание Punto 2004

Отзывы:

Похожие инструкции для Punto 2004

Бренды по названию

Популярные бренды