Fiat Punto 2004 Скачать руководство пользователя страница 116

Страница: 116 / 533

1.3 MULTIJET 16V

(75 & 90 HP)

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

The chart illustrates the characteristic curves of 4 injectors based on the control time (ET) for

various rail pressure levels. The axis of ordinates shows the amount of fuel delivered at every

injection instance (mm

/ciclo); the highlighted points are those where the measurements for

IMA classification are made.

The features of each electric injector are identified by a set of 9 alphanumeric characters

factory-printed on the electric injector body at the BOSCH premises.

The production plants of the POWERTRAIN engine have to receive and interpret the IMA

codes for every single electric injector (reading by means of a camera), in order to match the

same with the corresponding cylinder to which the injector is fitted, and also produce a label

that is put onto the timing belt cover. The FIAT bodywork plants match the engine

management control units with the respective software control strategies by means of special

in-line test equipment which reads the data shown on the label and then carries out the

operation with the diagnosis services described below.

FIAT PUNTO

116 / 532

The new spare control units and the ones supplied at the FIAT plant are delivered with a

standard default IMA code with a 00 hex value; the vehicles fitted with control units that have

Содержание Punto 2004

































































































































































































































































































































































































































































































































Результаты поиска

Содержание Punto 2004

Отзывы:

Похожие инструкции для Punto 2004

Бренды по названию

Популярные бренды

Fiat Punto 2004, Руководство по обучению

Результаты поиска

Содержание Punto 2004

Отзывы:

Похожие инструкции для Punto 2004

Бренды по названию

Популярные бренды