Fiat Punto 2004 Скачать руководство пользователя страница 518

Страница: 518 / 533

AIR CONDITIONER

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

MAX DEF function actuator;

rear heated window actuator.

D) connecting lines with:

Body Computer CAN network.

10.2.3 Compressor

Nuova Punto is equipped with the variable-displacement, magnetic clutch-free Denso 5SL12

compressor. It makes it possible to gradually vary the flow rate of the cooling fluid reaching the

evaporator; as a result, the anti-frost sensor would be redundant and has therefore not been

fitted to the system.

Control is based on the intake pressure value, according to the following logic:

low pressure: the compressor displacement tends to the minimum value;

high pressure: the displacement is increased.

This operating logic refers to the following actual conditions:

“low pressure” means that the load imposed to the air conditioner is such that it does not

require very high fluid flow rate;

“high pressure” means that a very high load is imposed to the air conditioner, and the required

amount of cooling fluid is great.

Operation

The pulley motion is transmitted continuously to the compressor shaft by means of jumpers,

referred to as “limiters” (3), which are interrupted in case of seizure due to a compressor fault,

thus preventing the pulley from getting stuck and, therefore, the auxiliary member belt from

being broken.

In order to reduce the torque fluctuations that generate noise, special dampers referred to as

“dumpers” (4) and an inertia ground (5) directly secured to the shaft are also used.

gb Fiat Grande Punto OK

517 / 532

Since the motion is always transmitted to the compressor shaft, the compressor switch-on/off

function is entrusted to the “ON/OFF” valve (6).

Содержание Punto 2004

































































































































































































































































































































































































































































































































Результаты поиска

Содержание Punto 2004

Отзывы:

Похожие инструкции для Punto 2004

Бренды по названию

Популярные бренды

Fiat Punto 2004, Руководство по обучению

Результаты поиска

Содержание Punto 2004

Отзывы:

Похожие инструкции для Punto 2004

Бренды по названию

Популярные бренды