Fiat Punto 2004 Скачать руководство пользователя страница 529

Страница: 529 / 533

SUNROOF

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

11.2 Operation

Control mask

The “Skydome” sunroof is operated by pressing the opening (A) and closing (B) buttons

located in the mask close to the front central ceiling light fixture. The operation logic described

below is implemented through actuation of an electric motor managed by an electronic control

unit.

The sunroof movements, obtained by the control button, are permitted only with

the panel ON (key-ON).

11.2.1 Sunroof opening

The front glass panel can be opened in two different ways, by pressing the respective button

(on the opening side) upon key-ON:

automatic opening

: by pressing the button on the “opening” side for more than 300 ms, the

front glass panel (fully closed) will open to the “spoiler opening position”, so as to ensure very

low drag noise. By pressing the button again on the same side, the front glass panel will reach

the maximum opening position. Following the initial opening control, the glass panel may be

stopped at intermediate positions by pressing the button again.

Manual opening

: by pressing the button briefly (for 60 to 300 ms), the front glass panel (fully

closed) will move to open proportionally to the time (T) during which the button is pressed, and

will stop when the button is released. By pressing the button again and again on the same

side (still within the time range of 60 to 300 ms), the panel will jolt along until it reaches the

maximum opening position. This function allows the user to position the front panel at

intermediate positions with respect to the maximum opening position.

gb Fiat Grande Punto OK

528 / 532

Содержание Punto 2004

































































































































































































































































































































































































































































































































Результаты поиска

Содержание Punto 2004

Отзывы:

Похожие инструкции для Punto 2004

Бренды по названию

Популярные бренды

Fiat Punto 2004, Руководство по обучению

Результаты поиска

Содержание Punto 2004

Отзывы:

Похожие инструкции для Punto 2004

Бренды по названию

Популярные бренды