Fiat Punto 2004 Скачать руководство пользователя страница 427

Страница: 427 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

Example

The panel also displays the information sent by Convergence module through a dynamic

multi-message. The number of frames that can be received depends on the number of

characters sent by the Convergence module.

Examples

Displaying form the Convergence module (Matrix panel)

Telephone displaying

The Convergence status and the information sent by the Convergence module will be

displayed on one single screen.

Navigator displaying

The following information is displayed:

Navigation pictograph

Distance to the next turn

Unit of measurement

Name of the street or road

Logistic mode

gb Fiat Grande Punto OK

426 / 532

This function can be actuated/deactivated only through the diagnostic network and makes it

possible to cut down consumption (current absorbed) so as to prevent the battery from running

down.

Содержание Punto 2004

































































































































































































































































































































































































































































































































Результаты поиска

Содержание Punto 2004

Отзывы:

Похожие инструкции для Punto 2004

Бренды по названию

Популярные бренды

Fiat Punto 2004, Руководство по обучению

Результаты поиска

Содержание Punto 2004

Отзывы:

Похожие инструкции для Punto 2004

Бренды по названию

Популярные бренды