Fiat Punto 2004 Скачать руководство пользователя страница 428

Страница: 428 / 533

ELECTRIC

SYSTEM

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

In particular, the vehicle board disables the following displaying (upon key-OFF and key-ON):

clock;

odometer (even when the front doors are opened or closed).

Warnings and messages

Message displaying (Comfort and Matrix panels).

The messages on the display are divided into four different classes:

high-priority anomalies;

low-priority anomalies;

warning messages (e.g. doors/boot open);

feedback (e.g. ASR ON/OFF).

When a fault occurs on the vehicle, the following will be displayed:

the warning light (and/or the icon on the Matrix display) corresponding to the fault;

the message corresponding to the description of the anomaly and/or the actions to be taken

by the driver. The display will illuminate at its maximum brightness (except for “Ice danger”

and the feedback messages).

The most important warnings and messages are accompanied by an acoustic signal

simultaneous with the message displaying. All the information contained in the display section

reserved for message displaying will be replaced by the information on the anomaly.

The messages are displayed upon very key-ON until the malfunction is identified and

remedied. In any case, the displaying can be interrupted by the driver by pressing the

“Menu/Esc” button. When the message displaying has been completed, and if the anomalous

condition persists, the warning light (and/or the icon on the Matrix panel) will remain ON.

In the event that several anomalies are found simultaneously, the display will show, in a

“rolling” fashion, each of the anomaly messages/ideographs over the duration of one

displaying cycle.

All the messages that fall within the abovementioned four classes are managed as follows:

Comfort panel: on displaying strings, each of them lasts 1.5 seconds max. and occupies 5

rows max (these strings make up a displaying cycle);

gb Fiat Grande Punto OK

427 / 532

Matrix panel: on one single screen.

Содержание Punto 2004

































































































































































































































































































































































































































































































































Результаты поиска

Содержание Punto 2004

Отзывы:

Похожие инструкции для Punto 2004

Бренды по названию

Популярные бренды

Fiat Punto 2004, Руководство по обучению

Результаты поиска

Содержание Punto 2004

Отзывы:

Похожие инструкции для Punto 2004

Бренды по названию

Популярные бренды