Endress+Hauser iTEMP TMT85 Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 100

background image

Operation via FOUNDATION Fieldbus

TM

iTEMP TMT85

82

Hauser

Parameter

Write access
with operating
mode
(MODE_BLK)

Description

Sensor range (SENSOR_
RANGE)

Read only
(EU_100, EU_0)
OOS
(UNITS_INDEX,
DECIMAL)

Physical measuring range of the sensor:
EU_100 (upper sensor range limit)
EU_0 (lower sensor range limit)
UNITS_INDEX (unit of the SENSOR_VALUE)
DECIMAL (number of decimal places for the
SENSOR_VALUE. This does not affect the measured value
display.)

Sensor offset (SENSOR_
OFFSET)

OOS

Offset of the SENSOR_VALUE
The following values are permitted:
• -10 to +10 for Celsius, Kelvin, mV and Ohm
• -18 to +18 for Fahrenheit, Rankine

2-wire compensation
(TWO_WIRE_
COMPENSATION)

OOS

Two-wire compensation
The following values are permitted:
0 to 30 Ω

Sensor serial number
(SENSOR_SN)

AUTO - OOS

Sensor serial number

Sensor max. indicator
(SENSOR_MAX_ INDICATOR)

AUTO - OOS

Max. indicator of the SENSOR_VALUE
Is stored in the non-volatile memory in intervals of 10
minutes. Can be reset.

Sensor min. indicator
SENSOR_MIN_ INDICATOR

AUTO - OOS

Min. indicator of the SENSOR_VALUE
Is stored in the non-volatile memory in intervals of 10
minutes. Can be reset.

Mains filter (MAINS_FILTER)

OOS

Mains filter for the A/D converter

Calibration highest point
(CAL_POINT_HI)

OOS

Upper point for linear characteristic calibration (this
affects offset and slope).



To be able to write this parameter,
"SENSOR_CAL_METHOD" must be set to "User trim
standard calibration".

Calibration lowest point
(CAL_POINT_LO)

OOS

Lower point for linear characteristic calibration (this
affects offset and slope).



To be able to write this parameter,
"SENSOR_CAL_METHOD" must be set to "User trim
standard calibration".

Calibration minimum span
(CAL_MIN_SPAN)

OOS

Span of the measurement range, depending on the
configured sensor type.

Calibration unit (CAL_UNIT)

Read only

Unit for sensor calibration.

Sensor calibration method
(SENSOR_CAL_ METHOD)

OOS

Factory trim standard calibration:
Sensor linearization with the factory calibration values
User trim standard calibration:
Sensor linearization with the values CAL_POINT_HI and
CAL_POINT_LO



The original linearization can be restored by
resetting this parameter to "Factory trim standard
calibration". The Transducer Block makes a wizard
available (User Sensor Trim) for linear characteristic
calibration.

Sensor calibration location
(SENSOR_CAL_ LOC)

AUTO - OOS

Name of the location where the sensor calibration was
performed.

Sensor calibration date
(SENSOR_CAL_ DATE)

AUTO - OOS

Date and time of the calibration.

Sensor calibration who
(SENSOR_CAL_ WHO)

AUTO - OOS

Name of the person responsible for the calibration.

«
...
80
81
82
83
84
...
»

Содержание iTEMP TMT85





































































































Отзывы:

Нет отзывов

Похожие инструкции для iTEMP TMT85

Бренд: NCTE Страницы: 10

Бренд: Mahr Страницы: 384

Бренд: YOKOGAWA Страницы: 2

ADMAG TI Series

Бренд: YOKOGAWA Страницы: 8

Бренд: Energic Plus Страницы: 12

Бренд: Wavetronix Страницы: 14

Бренд: CA.MI Страницы: 68

Бренд: Ecolab Страницы: 95

Бренд: Alfa Laval Страницы: 18

Бренд: Ocean Reef Страницы: 24

VBOX Touch Motorsport V1

Бренд: Racelogic Страницы: 15

Бренд: PRESIDIUM Страницы: 86

Бренд: Seca Страницы: 280

Бренд: General Страницы: 12

my mp3 grand piano

Бренд: ItsImagical Страницы: 5

Бренд: Voweek Страницы: 20

Бренд: RADWAG Страницы: 12

Бренд: Chauvin Arnoux Страницы: 87

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды