Endress+Hauser iTEMP TMT85 Скачать руководство пользователя страница 84

Страница: 84 / 100

Operation via FOUNDATION Fieldbus

iTEMP TMT85

Hauser

14.3.8 Transducer Block "Advanced Diagnostic"

The "Advanced Diagnostic" Transducer Block is used to configure and display all the

diagnostic functions of the transmitter.
Functions such as
• Corrosion detection

• Drift detection

• Ambient temperature monitoring
are displayed here.

Corrosion monitoring

Sensor connection cable corrosion can lead to false measured value readings. Therefore

the unit offers the possibility of detecting corrosion before a measured value is affected.

Corrosion monitoring is only possible for RTDs with a 4-wire connection and

thermocouples (see also →  43).
Drift detection can be configured with the SENSOR_DRIFT_MONITORING parameter. Drift

detection can be enabled or disabled. If drift detection is enabled and a drift occurs, an

error or maintenance request is generated. A distinction is made between 2 specific modes

(SENSOR_ DRIFT_MODE). In the 'Overshooting' mode, a status message is generated if the

limit value (SENSOR_DRIFT_ALERT_VALUE) for the drift is overshot, or if the limit value

is undershot in the 'Undershooting' mode.

A0042928

 22

Drift detection

'Undershooting' mode

'Overshooting' mode

Drift

L+,
L-

Upper (+) or lower (-) limit value

Time

Error or request for maintenance, depending on the setting

Содержание iTEMP TMT85





































































































Результаты поиска

Содержание iTEMP TMT85

Отзывы:

Похожие инструкции для iTEMP TMT85

Бренды по названию

Популярные бренды

Endress+Hauser iTEMP TMT85, Руководство по эксплуатации

Результаты поиска

Содержание iTEMP TMT85

Отзывы:

Похожие инструкции для iTEMP TMT85

Бренды по названию

Популярные бренды